root / plugins / other / ipmitool_sensor_ @ 6685d69a
Historique | Voir | Annoter | Télécharger (15,8 ko)
| 1 | 6685d69a | Jun Futagawa | #!/usr/bin/perl -w |
|---|---|---|---|
| 2 | # |
||
| 3 | # Wildcard plugin to monitor sensor by using ipmitool sensor program. |
||
| 4 | # |
||
| 5 | # Contributed by Jun Futagawa |
||
| 6 | # This script is based on sensors_ plugin. |
||
| 7 | # |
||
| 8 | # Usage: |
||
| 9 | # ln -s /usr/share/munin/plugins/ipmitool_sensor_ /etc/munin/plugins/ipmitool_sensor_fan |
||
| 10 | # ln -s /usr/share/munin/plugins/ipmitool_sensor_ /etc/munin/plugins/ipmitool_sensor_temp |
||
| 11 | # ln -s /usr/share/munin/plugins/ipmitool_sensor_ /etc/munin/plugins/ipmitool_sensor_volt |
||
| 12 | # |
||
| 13 | # Requirements: |
||
| 14 | # - OpenIPMI tool (ipmitool command) |
||
| 15 | # |
||
| 16 | # Note: |
||
| 17 | # - Sensor names are read from the output of the ipmitool sensor program. |
||
| 18 | # |
||
| 19 | # Add the following to your /etc/munin/plugin-conf.d/munin-node: |
||
| 20 | # |
||
| 21 | # [ipmitool_sensor*] |
||
| 22 | # user root |
||
| 23 | # timeout 20 |
||
| 24 | # |
||
| 25 | # If you want to use "ipmitool sdr", add the following: |
||
| 26 | # Note: When you use this, the threshold provided by the sensor board is not used. |
||
| 27 | # |
||
| 28 | # [ipmitool_sensor*] |
||
| 29 | # user root |
||
| 30 | # timeout 20 |
||
| 31 | # env.ipmitool_options sdr |
||
| 32 | # |
||
| 33 | # Parameters supported: |
||
| 34 | # |
||
| 35 | # config |
||
| 36 | # autoconf |
||
| 37 | # suggest |
||
| 38 | # |
||
| 39 | # Configurable variables |
||
| 40 | # |
||
| 41 | # ipmitool - ipmitool command (default: ipmitool) |
||
| 42 | # ipmitool_options - ipmitool command options (default: sensor) |
||
| 43 | # sdr: you can use 'sdr' instead of sensor. |
||
| 44 | # cache_file - cache file |
||
| 45 | # (default: /var/lib/munin/plugin-state/plugin-ipmitool_sensor.cache) |
||
| 46 | # cache_expires - cache expires (default: 275) |
||
| 47 | # |
||
| 48 | # fan_type_regex - Regular expression for unit of fan (default: RPM) |
||
| 49 | # temp_type_regex - Regular expression for unit of temp (default: degrees C) |
||
| 50 | # volt_type_regex - Regular expression for unit of volt (default: (Volts|Watts|Amps)) |
||
| 51 | # |
||
| 52 | # fan_warn_percent - Percentage over mininum for warning (default: 5) |
||
| 53 | # fan_lower_critical - Preferred lower critical value for fan |
||
| 54 | # fan_upper_critical - Preferred upper critical value for fan |
||
| 55 | # temp_lower_critical - Preferred lower critical value for temp |
||
| 56 | # temp_lower_warning - Preferred lower warining value for temp |
||
| 57 | # temp_upper_warning - Preferred upper warning value for temp |
||
| 58 | # temp_upper_critical - Preferred upper critical value for temp |
||
| 59 | # volt_warn_percent - Percentage over mininum/under maximum for warning |
||
| 60 | # Narrow the voltage bracket by this. (default: 20) |
||
| 61 | # |
||
| 62 | # $Log$ |
||
| 63 | # Revision 1.4 2009/02/08 23:51:00 jfut |
||
| 64 | # Support "ipmitool sdr". |
||
| 65 | # Add Watts and Amp as voltage unit. |
||
| 66 | # Add fan_type_regex/temp_type_regex/volt_type_regex as option of sensor type. |
||
| 67 | # |
||
| 68 | # Revision 1.3 2008/11/11 13:55:00 jfut |
||
| 69 | # Add infinity value check for HP ProLiant DL160. |
||
| 70 | # Add preferred value option for fan and temp. |
||
| 71 | # |
||
| 72 | # Revision 1.2 2008/10/28 19:21:22 jfut |
||
| 73 | # Add file check. |
||
| 74 | # |
||
| 75 | # Revision 1.1 2008/10/27 18:52:31 jfut |
||
| 76 | # Add cache mechanism. |
||
| 77 | # |
||
| 78 | # Revision 1.0 2008/10/27 14:25:12 jfut |
||
| 79 | # Initial release. |
||
| 80 | # |
||
| 81 | # Magic markers: |
||
| 82 | #%# family=manual |
||
| 83 | #%# capabilities=autoconf suggest |
||
| 84 | |||
| 85 | use strict; |
||
| 86 | |||
| 87 | $ENV{'LANG'} = "C"; # Force parseable output from sensors.
|
||
| 88 | $ENV{'LC_ALL'} = "C"; # Force parseable output from sensors.
|
||
| 89 | my $IPMITOOL = $ENV{'ipmitool'} || 'ipmitool';
|
||
| 90 | my @IPMITOOL_OPTS = exists $ENV{'ipmitool_options'} ? split(/\s+/, $ENV{'ipmitool_options'}) : ('sensor');
|
||
| 91 | |||
| 92 | my $CACHE_DIR = "/var/lib/munin/plugin-state"; |
||
| 93 | my $CACHE_FILE = $ENV{'cache_file'} || "$CACHE_DIR/plugin-ipmitool_sensor.cache";
|
||
| 94 | my $CACHE_EXPIRES = $ENV{'cache_expires'} || 275;
|
||
| 95 | |||
| 96 | my %config = ( |
||
| 97 | fan => {
|
||
| 98 | regex => exists $ENV{'fan_type_regex'} ? qr/$ENV{'fan_type_regex'}/im : qr/RPM/im,
|
||
| 99 | title => 'IPMITool Sensor: Fans', |
||
| 100 | vtitle => 'RPM', |
||
| 101 | print_threshold => \&fan_threshold, |
||
| 102 | graph_args => '--base 1000 -l 0' |
||
| 103 | }, |
||
| 104 | temp => {
|
||
| 105 | regex => exists $ENV{'temp_type_regex'} ? qr/$ENV{'temp_type_regex'}/im : qr/degrees C/im,
|
||
| 106 | title => 'IPMITool Sensor: Temperatures', |
||
| 107 | vtitle => 'Celsius', |
||
| 108 | print_threshold => \&temp_threshold, |
||
| 109 | graph_args => '--base 1000 -l 0' |
||
| 110 | }, |
||
| 111 | volt => {
|
||
| 112 | regex => exists $ENV{'volt_type_regex'} ? qr/$ENV{'volt_type_regex'}/im : qr/(Volts|Watts|Amps)/im,
|
||
| 113 | title => 'IPMITool Sensor: Voltages', |
||
| 114 | vtitle => '_AUTO_DETECT_FAILED_', |
||
| 115 | print_threshold => \&volt_threshold, |
||
| 116 | graph_args => '--base 1000' |
||
| 117 | }, |
||
| 118 | ); |
||
| 119 | |||
| 120 | if (defined $ARGV[0] and $ARGV[0] eq 'autoconf') {
|
||
| 121 | close(STDERR); |
||
| 122 | my $ret = system($IPMITOOL); |
||
| 123 | open (STDERR, ">&STDOUT"); |
||
| 124 | if ($ret == 0 || $ret == 256) {
|
||
| 125 | print "yes\n"; |
||
| 126 | exit 0; |
||
| 127 | } else {
|
||
| 128 | print "no (program $IPMITOOL not found)\n"; |
||
| 129 | } |
||
| 130 | exit 1; |
||
| 131 | } |
||
| 132 | |||
| 133 | if (defined $ARGV[0] and $ARGV[0] eq 'suggest') {
|
||
| 134 | my $text = get_sensor_data(); |
||
| 135 | my $alltext = join('\n', @{$text});
|
||
| 136 | foreach my $func (keys %config) {
|
||
| 137 | print $func, "\n" if $alltext =~ $config{$func}->{regex};
|
||
| 138 | } |
||
| 139 | exit; |
||
| 140 | } |
||
| 141 | |||
| 142 | $0 =~ /ipmitool_sensor_(.+)*$/; |
||
| 143 | my $func = $1; |
||
| 144 | exit 2 unless defined $func; |
||
| 145 | |||
| 146 | my $text = get_sensor_data(); |
||
| 147 | my $sensor = 1; |
||
| 148 | |||
| 149 | if (defined $ARGV[0] and $ARGV[0] eq 'config') {
|
||
| 150 | # detect the unit of volt |
||
| 151 | if ($func eq 'volt') {
|
||
| 152 | foreach my $line (@{$text}) {
|
||
| 153 | if ($line =~ /$config{$func}->{regex}/) {
|
||
| 154 | my ($label, $value, $unit, $lcr, $lnc, $unc, $ucr) = &get_sensor_items($line, $config{$func}->{regex});
|
||
| 155 | $config{$func}->{vtitle} = $unit;
|
||
| 156 | last; |
||
| 157 | } |
||
| 158 | } |
||
| 159 | $text = get_sensor_data(); |
||
| 160 | } |
||
| 161 | |||
| 162 | # print header |
||
| 163 | print "graph_title $config{$func}->{title}\n";
|
||
| 164 | print "graph_vtitle $config{$func}->{vtitle}\n";
|
||
| 165 | print "graph_args $config{$func}->{graph_args}\n";
|
||
| 166 | print "graph_category sensors\n"; |
||
| 167 | |||
| 168 | # print data |
||
| 169 | foreach my $line (@{$text}) {
|
||
| 170 | if ($line =~ /$config{$func}->{regex}/) {
|
||
| 171 | my ($label, $value, $unit, $lcr, $lnc, $unc, $ucr) = &get_sensor_items($line, $config{$func}->{regex});
|
||
| 172 | if (&is_valid_value($value)) {
|
||
| 173 | print "$func$sensor.label $label\n"; |
||
| 174 | $config{$func}->{print_threshold}->($func.$sensor, $lcr, $lnc, $unc, $ucr);
|
||
| 175 | print "$func$sensor.graph no\n" if exists $ENV{"ignore_$func$sensor"};
|
||
| 176 | $sensor++; |
||
| 177 | } |
||
| 178 | } |
||
| 179 | } |
||
| 180 | exit 0; |
||
| 181 | } |
||
| 182 | |||
| 183 | foreach my $line (@{$text}) {
|
||
| 184 | if ($line =~ /$config{$func}->{regex}/) {
|
||
| 185 | my ($label, $value, $unit, $lcr, $lnc, $unc, $ucr) = &get_sensor_items($line, $config{$func}->{regex});
|
||
| 186 | # for debug |
||
| 187 | # print "$func$sensor.value [$label] [$value] [$lcr] [$lnc] [$unc] [$ucr]\n"; |
||
| 188 | if (&is_valid_value($value)) {
|
||
| 189 | print "$func$sensor.value $value\n"; |
||
| 190 | $sensor++; |
||
| 191 | } |
||
| 192 | } |
||
| 193 | } |
||
| 194 | |||
| 195 | sub get_sensor_data {
|
||
| 196 | my $text = undef; |
||
| 197 | if (-f $CACHE_FILE) {
|
||
| 198 | my $cache_timestamp = (stat($CACHE_FILE))[9]; |
||
| 199 | if ($CACHE_EXPIRES == -1 || time - $cache_timestamp <= $CACHE_EXPIRES) {
|
||
| 200 | open(IN, "<", $CACHE_FILE) or die "Could not open \"$CACHE_FILE\" for reading\n"; |
||
| 201 | while (<IN>) {
|
||
| 202 | push (@{$text}, $_);
|
||
| 203 | } |
||
| 204 | close(IN); |
||
| 205 | } |
||
| 206 | } |
||
| 207 | if (! defined $text) {
|
||
| 208 | my $pid = open(EXE, '-|'); |
||
| 209 | if ($pid == 0) {
|
||
| 210 | exec($IPMITOOL, @IPMITOOL_OPTS); |
||
| 211 | } elsif (defined $pid) {
|
||
| 212 | while(<EXE>) {
|
||
| 213 | push (@{$text}, $_);
|
||
| 214 | } |
||
| 215 | close(EXE); |
||
| 216 | } else {
|
||
| 217 | die "fork failed: $!"; |
||
| 218 | } |
||
| 219 | if (-w $CACHE_DIR) {
|
||
| 220 | open(OUT, ">", $CACHE_FILE) or die "Could not open \"$CACHE_FILE\" for writing\n"; |
||
| 221 | foreach my $line (@{$text}) {
|
||
| 222 | print OUT "$line"; |
||
| 223 | } |
||
| 224 | close OUT; |
||
| 225 | } |
||
| 226 | } |
||
| 227 | return $text; |
||
| 228 | } |
||
| 229 | |||
| 230 | sub get_sensor_items {
|
||
| 231 | my ($line, $regex) = @_; |
||
| 232 | my @items = split(/\s*\|\s*/, $line); |
||
| 233 | my ($label, $value, $unit, $lcr, $lnc, $unc, $ucr) |
||
| 234 | = (trim($items[0]), trim($items[1]), trim($items[2]), trim($items[5]), trim($items[6]), trim($items[7]), trim($items[8])); |
||
| 235 | if ($#items == 9) {
|
||
| 236 | # ipmitool sensor |
||
| 237 | } elsif ($#items == 2) {
|
||
| 238 | # ipmitool sdr |
||
| 239 | if ($value =~ /$regex/) {
|
||
| 240 | $value = trim($`); |
||
| 241 | $unit = trim($1); |
||
| 242 | } |
||
| 243 | } |
||
| 244 | |||
| 245 | # some boards show data in incorrect order. |
||
| 246 | # - HP ProLiant ML110 G5 |
||
| 247 | # CPU FAN | 1434.309 | RPM | ok | 5537.099 | 4960.317 | 4859.086 | na | 937.383 | na |
||
| 248 | # SYSTEM FAN | 1506.932 | RPM | ok | 5952.381 | 5668.934 | 5411.255 | na | 937.383 | na |
||
| 249 | # - HP ProLiant DL160 |
||
| 250 | # FAN1 ROTOR1 | 7680.492 | RPM | ok | na | inf | na | na | 1000.400 | na |
||
| 251 | if (&is_valid_value($lcr) && &is_valid_value($ucr) && $lcr > $ucr || $lcr eq 'inf') {
|
||
| 252 | ($lcr, $lnc, $unc, $ucr) = ($ucr, $unc, $lnc, $lcr); |
||
| 253 | } |
||
| 254 | if (&is_valid_value($lnc) && &is_valid_value($unc) && $lnc > $unc || $lnc eq 'inf') {
|
||
| 255 | ($lcr, $lnc, $unc, $ucr) = ($ucr, $unc, $lnc, $lcr); |
||
| 256 | } |
||
| 257 | return ($label, $value, $unit, $lcr, $lnc, $unc, $ucr); |
||
| 258 | } |
||
| 259 | |||
| 260 | sub fan_threshold {
|
||
| 261 | my ($name, $lcr, $lnc, $unc, $ucr) = @_; |
||
| 262 | my $warn_percent = exists $ENV{fan_warn_percent} ? $ENV{fan_warn_percent} : 5;
|
||
| 263 | |||
| 264 | # lcr: lower critical |
||
| 265 | if (exists $ENV{fan_lower_critical}) {
|
||
| 266 | $lcr = $ENV{fan_lower_critical};
|
||
| 267 | } elsif (! &is_valid_value($lcr)) {
|
||
| 268 | if ($lcr eq 'inf') { $lcr = ''; }
|
||
| 269 | else { $lcr = '50'; }
|
||
| 270 | } |
||
| 271 | # lnc: lower warning |
||
| 272 | if (! &is_valid_value($lnc)) {
|
||
| 273 | if ($lnc eq 'inf') { $lnc = ''; }
|
||
| 274 | else { $lnc = ($lcr eq '') ? '' : $lcr * (100 + $warn_percent) / 100; }
|
||
| 275 | } |
||
| 276 | # ucr: upper critical |
||
| 277 | if (exists $ENV{fan_upper_critical}) {
|
||
| 278 | $ucr = $ENV{fan_upper_critical};
|
||
| 279 | } elsif (! &is_valid_value($ucr)) {
|
||
| 280 | if ($ucr eq 'inf') { $ucr = ''; }
|
||
| 281 | else { $ucr = '6000'; }
|
||
| 282 | } |
||
| 283 | # unc: upper warning |
||
| 284 | if (! &is_valid_value($unc)) {
|
||
| 285 | if ($unc eq 'inf') { $unc = ''; }
|
||
| 286 | else { $unc = ($ucr eq '') ? '' : $ucr * (100 - $warn_percent) / 100; }
|
||
| 287 | } |
||
| 288 | |||
| 289 | return unless ($lcr ne '' || $lnc ne '' || $unc ne '' || $ucr ne ''); |
||
| 290 | |||
| 291 | printf "$name.warning $lnc:$unc\n"; |
||
| 292 | printf "$name.critical $lcr:$ucr\n"; |
||
| 293 | } |
||
| 294 | |||
| 295 | sub temp_threshold {
|
||
| 296 | my ($name, $lcr, $lnc, $unc, $ucr) = @_; |
||
| 297 | |||
| 298 | # lcr: lower critical |
||
| 299 | if (exists $ENV{temp_lower_critical}) {
|
||
| 300 | $lcr = $ENV{temp_lower_critical};
|
||
| 301 | } elsif (! &is_valid_value($lcr)) {
|
||
| 302 | if ($lcr eq 'inf') { $lcr = ''; }
|
||
| 303 | else { $lcr = 5; }
|
||
| 304 | } |
||
| 305 | # lnc: lower warning |
||
| 306 | if (exists $ENV{temp_lower_warningl}) {
|
||
| 307 | $lnc = $ENV{temp_lower_warning};
|
||
| 308 | } elsif (! &is_valid_value($lnc)) {
|
||
| 309 | if ($lnc eq 'inf') { $lnc = ''; }
|
||
| 310 | else { $lnc = 10; }
|
||
| 311 | } |
||
| 312 | # unc: upper critical |
||
| 313 | if (exists $ENV{fan_upper_critical}) {
|
||
| 314 | $unc = $ENV{fan_upper_critical};
|
||
| 315 | } elsif (! &is_valid_value($unc)) {
|
||
| 316 | if ($unc eq 'inf') { $unc = ''; }
|
||
| 317 | else { $unc = '65'; }
|
||
| 318 | } |
||
| 319 | # ucr: upper warning |
||
| 320 | if (exists $ENV{upper_critical}) {
|
||
| 321 | $ucr = $ENV{upper_critical};
|
||
| 322 | } elsif (! &is_valid_value($ucr)) {
|
||
| 323 | if ($ucr eq 'inf') { $ucr = ''; }
|
||
| 324 | else { $ucr = '70'; }
|
||
| 325 | } |
||
| 326 | |||
| 327 | return unless ($lcr ne '' || $lnc ne '' || $unc ne '' || $ucr ne ''); |
||
| 328 | |||
| 329 | printf "$name.warning $lnc:$unc\n"; |
||
| 330 | printf "$name.critical $lcr:$ucr\n"; |
||
| 331 | } |
||
| 332 | |||
| 333 | sub volt_threshold {
|
||
| 334 | my ($name, $lcr, $lnc, $unc, $ucr) = @_; |
||
| 335 | my $warn_percent = exists $ENV{volt_warn_percent} ? $ENV{volt_warn_percent} : 20;
|
||
| 336 | |||
| 337 | if (! &is_valid_value($lcr)) { $lcr = ''; }
|
||
| 338 | if (! &is_valid_value($lnc)) { $lnc = ($lcr eq '') ? '' : $lcr * (100 + $warn_percent) / 100; }
|
||
| 339 | if (! &is_valid_value($ucr)) { $ucr = ''; }
|
||
| 340 | if (! &is_valid_value($unc)) { $unc = ($ucr eq '') ? '' : $ucr * (100 - $warn_percent) / 100; }
|
||
| 341 | |||
| 342 | return unless ($lcr ne '' || $lnc ne '' || $unc ne '' || $ucr ne ''); |
||
| 343 | |||
| 344 | printf "$name.warning $lnc:$unc\n"; |
||
| 345 | printf "$name.critical $lcr:$ucr\n"; |
||
| 346 | } |
||
| 347 | |||
| 348 | sub trim {
|
||
| 349 | my $value = shift; |
||
| 350 | if (defined $value) {
|
||
| 351 | $value =~ s/^\s*(.*?)\s*$/$1/; |
||
| 352 | } else {
|
||
| 353 | $value = 'na' |
||
| 354 | } |
||
| 355 | return $value; |
||
| 356 | } |
||
| 357 | |||
| 358 | sub is_valid_value() {
|
||
| 359 | my $value = shift; |
||
| 360 | if ($value eq 'na' || $value eq 'inf' || $value eq '') {
|
||
| 361 | return 0; |
||
| 362 | } else {
|
||
| 363 | return 1; |
||
| 364 | } |
||
| 365 | } |
||
| 366 | |||
| 367 | ######################################## |
||
| 368 | |||
| 369 | =head1 How to test |
||
| 370 | |||
| 371 | cache_file=ipmitool_sensor_ cache_expires=-1 ./ipmitool_sensor_volt |
||
| 372 | cache_file=ipmitool_sensor_ cache_expires=-1 ./ipmitool_sensor_volt config |
||
| 373 | cache_file=ipmitool_sensor_ cache_expires=-1 ./ipmitool_sensor_volt suggest |
||
| 374 | cache_file=ipmitool_sensor_ cache_expires=-1 ./ipmitool_sensor_volt autoconf |
||
| 375 | |||
| 376 | =head1 Test Data |
||
| 377 | |||
| 378 | =head2 ipmitool sensor |
||
| 379 | |||
| 380 | # HP ProLiant ML110 G5 |
||
| 381 | CPU FAN | 1434.309 | RPM | ok | 5537.099 | 4960.317 | 4859.086 | na | 937.383 | na |
||
| 382 | SYSTEM FAN | 1497.454 | RPM | ok | 5952.381 | 5668.934 | 5411.255 | na | 937.383 | na |
||
| 383 | System 12V | 12.152 | Volts | ok | na | na | na | na | na | na |
||
| 384 | System 5V | 5.078 | Volts | ok | na | na | na | na | na | na |
||
| 385 | System 3.3V | 3.271 | Volts | ok | na | na | na | na | na | na |
||
| 386 | CPU0 Vcore | 1.127 | Volts | ok | na | na | na | na | na | na |
||
| 387 | System 1.25V | 1.254 | Volts | ok | na | na | na | na | na | na |
||
| 388 | System 1.8V | 1.842 | Volts | ok | na | na | na | na | na | na |
||
| 389 | System 1.2V | 1.107 | Volts | ok | na | na | na | na | na | na |
||
| 390 | CPU0 Diode | na | degrees C | na | na | 20.000 | 25.000 | 85.000 | 90.000 | 95.000 |
||
| 391 | CPU0 Dmn 0 Temp | 24.500 | degrees C | ok | na | 0.000 | 0.000 | 97.000 | 100.000 | 100.500 |
||
| 392 | CPU0 Dmn 1 Temp | 29.000 | degrees C | ok | na | 0.000 | 0.000 | 97.000 | 100.000 | 100.500 |
||
| 393 | # HP ProLiant DL160 |
||
| 394 | FAN1 ROTOR1 | 7680.492 | RPM | ok | na | inf | na | na | 1000.400 | na |
||
| 395 | # HP ProLiant DL360 G5 |
||
| 396 | Fan Block 1 | 34.888 | unspecified | nc | na | na | 75.264 | na | na | na |
||
| 397 | Fan Block 2 | 29.792 | unspecified | nc | na | na | 75.264 | na | na | na |
||
| 398 | Fan Block 3 | 37.240 | unspecified | nc | na | na | 75.264 | na | na | na |
||
| 399 | Fan Blocks | 0.000 | unspecified | nc | na | na | 0.000 | na | na | na |
||
| 400 | Temp 1 | 40.000 | degrees C | ok | na | na | -64.000 | na | na | na |
||
| 401 | Temp 2 | 21.000 | degrees C | ok | na | na | -64.000 | na | na | na |
||
| 402 | Temp 3 | 30.000 | degrees C | ok | na | na | -64.000 | na | na | na |
||
| 403 | Temp 4 | 30.000 | degrees C | ok | na | na | -64.000 | na | na | na |
||
| 404 | Temp 5 | 28.000 | degrees C | ok | na | na | -64.000 | na | na | na |
||
| 405 | Temp 6 | na | degrees C | na | na | na | 32.000 | na | na | na |
||
| 406 | Temp 7 | na | degrees C | na | na | na | 32.000 | na | na | na |
||
| 407 | Power Meter | 214.000 | Watts | cr | na | na | 384.000 | na | na | na |
||
| 408 | Power Meter 2 | 220.000 | watts | cr | na | na | 384.000 | na | na | na |
||
| 409 | |||
| 410 | =head2 ipmitool sdr |
||
| 411 | |||
| 412 | # HP ProLiant ML110 G5 |
||
| 413 | CPU FAN | 1434.31 RPM | ok |
||
| 414 | SYSTEM FAN | 1497.45 RPM | ok |
||
| 415 | System 12V | 12.10 Volts | ok |
||
| 416 | System 5V | 5.08 Volts | ok |
||
| 417 | System 3.3V | 3.27 Volts | ok |
||
| 418 | CPU0 Vcore | 1.14 Volts | ok |
||
| 419 | System 1.25V | 1.25 Volts | ok |
||
| 420 | System 1.8V | 1.84 Volts | ok |
||
| 421 | System 1.2V | 1.11 Volts | ok |
||
| 422 | CPU0 Diode | disabled | ns |
||
| 423 | CPU0 Dmn 0 Temp | 23.50 degrees C | ok |
||
| 424 | CPU0 Dmn 1 Temp | 29 degrees C | ok |
||
| 425 | # HP ProLiant DL360 G5 |
||
| 426 | Fan Block 1 | 34.89 unspecifi | nc |
||
| 427 | Fan Block 2 | 29.79 unspecifi | nc |
||
| 428 | Fan Block 3 | 37.24 unspecifi | nc |
||
| 429 | Fan Blocks | 0 unspecified | nc |
||
| 430 | Temp 1 | 41 degrees C | ok |
||
| 431 | Temp 2 | 19 degrees C | ok |
||
| 432 | Temp 3 | 30 degrees C | ok |
||
| 433 | Temp 4 | 30 degrees C | ok |
||
| 434 | Temp 5 | 26 degrees C | ok |
||
| 435 | Temp 6 | disabled | ns |
||
| 436 | Temp 7 | disabled | ns |
||
| 437 | Power Meter | 208 Watts | cr |
||
| 438 | Power Meter 2 | 210 watts | cr |
||
| 439 | |||
| 440 | =cut |
||
| 441 | |||
| 442 | # vim:syntax=perl |